Navigating urban congestion: Optimizing LSTM with RNN in traffic prediction DOI
Surjeet Dalal,

Vivek Jaglan,

Akshat Agrawal

и другие.

AIP conference proceedings, Год журнала: 2024, Номер 3217, С. 030005 - 030005

Опубликована: Янв. 1, 2024

Язык: Английский

Supervised Machine learning models for predicting mechanical properties of dissimilar friction stir welded AA7075-AA5083 aluminum alloys DOI
Meghavath Mothilal, Atul Kumar

Measurement, Год журнала: 2025, Номер unknown, С. 116653 - 116653

Опубликована: Янв. 1, 2025

Язык: Английский

Процитировано

2
Influence of tool traverse speed on mechanical properties and fracture morphology of friction stir welded pure copper butt joints DOI
Puspendu Chandra Chandra, Arpan Kumar Mondal, N. Yadaiah

и другие.

Journal of Adhesion Science and Technology, Год журнала: 2024, Номер unknown, С. 1 - 14

Опубликована: Окт. 8, 2024

The key goal of this research was to study the effect traverse speed a tool on microstructural changes, mechanical properties and fracture morphology pure copper butted weld joint by friction stir welding technique. In study, other parameters like rotational (1000 rpm), axial force (4.2 kN), tilt angle (0˚) offset (0 mm) were fixed. A cylindrical with non-threaded tapered pin used fabricate joints. All joints produced varying speeds (11, 20 24 mm min−1) defect-free. It noticed that grains in zone tiny, well distributed homogeneous at min−1 owing adequate heat generation complete intermixing material zone. utmost tensile strength 187 MPa achieved welded attained min−1. observed densely populated dimple structure enhances ductility case

Язык: Английский

Процитировано

5
Optimization of Joint Strength in Friction Stir Welded Wood Plastic Composites Using ANFIS and Cheetah Optimizer DOI Creative Commons
Ammar H. Elsheikh,

Mohamad Elmiligy,

Ahmad Alkassas

и другие.

Journal of Materials Research and Technology, Год журнала: 2024, Номер unknown

Опубликована: Дек. 1, 2024

Язык: Английский

Процитировано

3
Adaptive Multigrid Long Short-Term Memory Algorithm for Improved Air Quality Forecasting DOI

G. Shanmugasundar,

Janjhyam Venkata Naga Ramesh,

B. Murali

и другие.

Studies in computational intelligence, Год журнала: 2025, Номер unknown, С. 267 - 282

Опубликована: Янв. 1, 2025

Язык: Английский

Процитировано

0
Optimization of welding strength in the tungsten inert gas welding process for aluminium alloys DOI Creative Commons
Amit Gupta, Rajeev Ranjan, Róbert Čep

и другие.

Frontiers in Mechanical Engineering, Год журнала: 2025, Номер 11

Опубликована: Май 23, 2025

Aluminium alloys, particularly AA 6065 T6, are widely used in automotive components such as coolers and radiators due to their excellent strength-to-weight ratio corrosion resistance. However, welding these alloys presents significant challenges, the weld joints prone thermal stresses, leading defects eventual failure. To address this issue, optimizing PCTIG (Pulsed Current Tungsten Inert Gas) process parameters is crucial for achieving superior mechanical properties, tensile strength. This study investigates influence of peak current, base frequency on strength T6 aluminium alloy with varying thicknesses (3 mm, 6 10 mm). Regression models developed predict across factorial space, ANOVA applied assess significance each parameter. Experimental results identify optimal strengths 179.50 MPa, 188.92 201.22 MPa 3 mm thick materials, respectively, set at 180 A 60 2 Hz frequency. Validation through simulation software corroborates findings, confirming effectiveness optimized producing defect-free, high-strength suitable applications.

Язык: Английский

Процитировано

0
A Comprehensive Review on the Integration of Artificial Intelligence in Friction Stir Welding for Monitoring, Modelling, and Process Optimization DOI Creative Commons
Mostafa Akbari,

Ezatollah Hassanzadeh,

Yaghuob Dadgar Asl

и другие.

Journal of Advanced Joining Processes, Год журнала: 2025, Номер unknown, С. 100316 - 100316

Опубликована: Май 1, 2025

Язык: Английский

Процитировано

0
Intelligent Manufacturing in Aerospace: Integrating Industry 4.0 Technologies for Operational Excellence and Digital Transformation DOI
Vineet Bhatia, Sumati Sidharth, Sanjeev Kumar Khare

и другие.

Springer series in advanced manufacturing, Год журнала: 2024, Номер unknown, С. 389 - 434

Опубликована: Янв. 1, 2024

Язык: Английский

Процитировано

2
Exploring the Challenges of Integrating Lean Green Practices in Industry 4.0 Manufacturing Frameworks: An Empirical Study DOI
Rajesh Kumar, Rajender Kumar,

Ashwini Kumar

и другие.

Springer series in advanced manufacturing, Год журнала: 2024, Номер unknown, С. 277 - 292

Опубликована: Янв. 1, 2024

Язык: Английский

Процитировано

2
Digital Twin Integration for Enhanced Control in FDM 3D Printing DOI
Sourabh Anand,

Manoj Kumar Satyarthi,

Pushpendra S. Bharti

и другие.

Springer series in advanced manufacturing, Год журнала: 2024, Номер unknown, С. 373 - 388

Опубликована: Янв. 1, 2024

Язык: Английский

Процитировано

1
Progressive Automation: Mapping the Horizon of Smart Manufacturing with RoboDK Workstations and Industry 4.0 DOI
Mukul Kumar, Sourabh Anand, Pushpendra S. Bharti

и другие.

Springer series in advanced manufacturing, Год журнала: 2024, Номер unknown, С. 335 - 354

Опубликована: Янв. 1, 2024

Язык: Английский

Процитировано

1