Recent advances in lignocellulosic fibers for developing sustainable composites: extraction, surface modification and characterization- A review DOI
P. Barman,

P. S. Rakesh,

M. Somaiah Chowdary

et al.

International Journal of Biological Macromolecules, Journal Year: 2025, Volume and Issue: unknown, P. 143360 - 143360

Published: April 1, 2025

Language: Английский

A study of mechanical properties and performance of bamboo fiber/polymer composites DOI Creative Commons
Mohammad Khalid, Rozli Zulkifli,

Mohd Faizal Mat Tahir

et al.

Results in Engineering, Journal Year: 2024, Volume and Issue: 23, P. 102396 - 102396

Published: June 13, 2024

Language: Английский

Citations

16
Experimental Investigation of High Filler Loading of SiO2 on the Mechanical and Dynamic Mechanical Analysis of Natural PALF fibre-Based Hybrid Composite DOI

G. Velmurugan,

V. Siva Shankar, M. Kalil Rahiman

et al.

Silicon, Journal Year: 2023, Volume and Issue: 15(13), P. 5587 - 5602

Published: April 17, 2023

Language: Английский

Citations

23
The structural, dielectric, and dynamic properties of NaOH-treated Bambusa tulda reinforced biocomposites—an experimental investigation DOI
Abir Saha, Nikhil Dilip Kulkarni, Mukesh Kumar

et al.

Biomass Conversion and Biorefinery, Journal Year: 2023, Volume and Issue: 14(20), P. 26247 - 26266

Published: Aug. 11, 2023

Language: Английский

Citations

23
Development of Bambusa tulda fiber-micro particle reinforced hybrid green composite: A sustainable solution for tomorrow's challenges in construction and building engineering DOI
Abir Saha, Nikhil Dilip Kulkarni,

Poonam Kumari

et al.

Construction and Building Materials, Journal Year: 2024, Volume and Issue: 441, P. 137486 - 137486

Published: July 24, 2024

Language: Английский

Citations

13
Characterization of alkali-treated cellulosic fibers derived from Calamus tenuis canes as a potential reinforcement for polymer composites DOI
Arup Kar, Dip Saikia, P. Narayanasamy

et al.

Biomass Conversion and Biorefinery, Journal Year: 2024, Volume and Issue: 15(5), P. 7881 - 7899

Published: April 8, 2024

Language: Английский

Citations

12
Short carbon fiber-reinforced PLA composites: influence of 3D-printing parameters on the mechanical and structural properties DOI Creative Commons

Rasha Alkabbanie,

Bülent Aktaş, Gökhan Demircan

et al.

Iranian Polymer Journal, Journal Year: 2024, Volume and Issue: 33(8), P. 1065 - 1074

Published: April 15, 2024

Abstract 3D printing, particularly “fused filament fabrication” (FFF), plays a crucial role in Industry 4. FFF is widely used for creating complex structures and multi-material parts across various industries such as food industry, fashion manufacturing sectors. The properties of FFF-produced objects are remarkably affected by printing parameters. This study explores the impact parameters addition short carbon fibers on strength polylactic acid (PLA) printed samples. lowering layer height, increasing feed rate extrusion temperature boost strength, while smaller raster angle enhances it. Meanwhile, an improved flexural achieved adjusting temperature, angle. Higher temperatures enhance tensile microstructure, reduce porosity. Lower height improves (28.05% increase 0.1 mm height), higher boosts strengths (12.56% improvement 7 3 /s rate), elevated (14.49% 230 °C temperature) but (14.44% decrease). Incorporating PLA negatively affects microstructure increases crystallinity, raising melting cold-crystallization temperature. introduction into results interplay mechanical thermal properties. Graphical abstract

Language: Английский

Citations

8
Various factors affecting the fatigue performance of natural fiber-reinforced polymer composites: a systematic review DOI
Sumit Bhowmik, Santosh Kumar, Vijay Kumar Mahakur

et al.

Iranian Polymer Journal, Journal Year: 2023, Volume and Issue: 33(2), P. 249 - 271

Published: Nov. 6, 2023

Language: Английский

Citations

22
Development of Bambusa tulda-reinforced different biopolymer matrix green composites and MCDM-based sustainable material selection for automobile applications DOI
Abir Saha, Nikhil Dilip Kulkarni,

Poonam Kumari

et al.

Environment Development and Sustainability, Journal Year: 2023, Volume and Issue: unknown

Published: Dec. 26, 2023

Language: Английский

Citations

22
The development of a low‐cost, sustainable bamboo‐based flexible bio composite for impact sensing and mechanical energy harvesting applications DOI
Nikhil Dilip Kulkarni, Abir Saha, Poonam Kumari

et al.

Journal of Applied Polymer Science, Journal Year: 2023, Volume and Issue: 140(29)

Published: May 9, 2023

Abstract An increasing trend in creating materials with a greater extent of sustainability from an ecological and financial perspective involves usage bio resources industrial residues. In this paper, leftover bamboo micro particles (BMP) factories were collected used as fillers polyvinylidene fluoride (PVDF) matrix varying concentrations (1, 3, 5, 7, 9 wt.%) to fabricate low‐cost composite films using solvent casting route for mechanical energy harvesting purpose. Out the prepared samples, PVDF 5 wt.% BMP showed maximum electroactive phase content (82%), tensile strength (34.23 MPa), piezoelectric voltage (6.5 V) among untreated samples. is then subjected NaOH treatment further enhancement overall performance. treated also 467% increment output 235% current compared pure PVDF. The measured under impact loading conditions determine its suitability sensor. A bamboo‐based sensor that highly sensitive cost‐effective opens enormous possibilities circular economies.

Language: Английский

Citations

19
Comparison of the Tensile Strength of Single Natural Fibers DOI

Endalkachew Gashawtena,

Addis Kidane,

Belete Sirahbizu

et al.

Cellulose, Journal Year: 2024, Volume and Issue: 31(8), P. 4833 - 4848

Published: April 17, 2024

Language: Английский

Citations

6