Effect of Annealing Temperature on the Microstructural and Mechanical Properties of Wire Rod Steel Annealed Using a Biomass Gasifier DOI Creative Commons

Pathompong Chootapa,

Songkran Wiriyasart,

Sommas Kaewluan

et al.

Energies, Journal Year: 2025, Volume and Issue: 18(8), P. 1912 - 1912

Published: April 9, 2025

Natural and liquefied petroleum gases are widely used in industrial heat treatment. However, the rising cost of gas, combined with increased demand, has significantly impacted production costs environment. The annealing process typically relies on natural or as primary source. In this study, we aimed to investigate use biomass fuel a replacement for fossil fuels evaluate mechanical properties microstructure wire rod steel after using indirect from gasifier. We experimented examine effects temperatures 650 °C, 700 °C (below critical temperature Ac1), 750 (above Ac1 but below upper Ac3). batch furnace, made stainless steel, was modified traditional furnace that originally CNG LPG gas burners. It adapted into connected cross-draft furnace’s interior designed spiral cooling fins minimize energy consumption shorten time. Additionally, it substitute fuel, reducing environmental pollution. coated thermal insulation, gasifier stove device air feeding at 20 m3/h secondary supplied constant flow rate 32 m3/h, 36 40 m3/h. As source, eucalyptus. were measured terms tensile strength torsion, following TIS 138-2562 standard. This standard specifies must be least 260 MPa. Regarding requirements state withstand 75 rounds twisting without breaking. Our results showed soaking time 30 min subsequent 24 h, values 494.82, 430.87, 381.33 MPa, respectively. torsion 126.92, 125.8, 125.76 rounds, ferrite grain size temperature, reaching maximum °C. total duration each 2 h 10

Language: Английский

Low-carbon, hydrogen-rich syngas from sorption-enhanced gasification: A review DOI Creative Commons
Godknows Dziva,

Jonas Weitzel,

Peicai Cui

et al.

Carbon Capture Science & Technology, Journal Year: 2025, Volume and Issue: unknown, P. 100372 - 100372

Published: Jan. 1, 2025

Language: Английский

Citations

1
Integration of sorbent enhanced in hydrothermal waste transformation for negative CO2 emission fuel production: Techno-economic assessments DOI

M. Sow,

Mohamed M. Ibrahim, Abdelghafour Zaabout

et al.

Energy Conversion and Management, Journal Year: 2025, Volume and Issue: 326, P. 119519 - 119519

Published: Jan. 23, 2025

Language: Английский

Citations

1
Advancement in neutral and negative emissions production of ammonia from carbonaceous sources: A review DOI Creative Commons
Yongxing Zhang, Jafar Zanganeh, Behdad Moghtaderi

et al.

International Journal of Hydrogen Energy, Journal Year: 2025, Volume and Issue: 109, P. 40 - 62

Published: Feb. 8, 2025

Language: Английский

Citations

1
Development and assessment of a biomass-gasification based multigenerational plant for production of hydrogen and ammonia fuels DOI
Yunus Emre Yüksel, Murat Öztürk, İbrahim Dinçer

et al.

Fuel, Journal Year: 2024, Volume and Issue: 380, P. 133187 - 133187

Published: Sept. 23, 2024

Language: Английский

Citations

6
Modelling of green ammonia production based on solid oxide cells as electrolyser and oxygen separator for Haber-Bosch loop decarbonization DOI Creative Commons
Fiammetta Rita Bianchi, Bárbara Bosio

International Journal of Hydrogen Energy, Journal Year: 2024, Volume and Issue: unknown

Published: July 1, 2024

Ammonia is a well-known chemical and rising candidate as hydrogen carrier. Nevertheless, its synthesis process decarbonization preliminary target. Since the Haber-Bosch loop still best path guaranteeing high yield capacity, alternative nitrogen upstream production steps have to be identified. Based on water electrolysis, Power-to-Ammonia application allows for coupling performing traditional with renewables. This configuration would minimise environmental impacts make decentralised local feasible; nevertheless, competitiveness strictly depends reducing electricity demand. Looking low consumption electrolysis technologies, work presents high-temperature solid oxide cells one of most competitive solutions showing double operation, generator oxygen concentrator, which leads H2–N2 mixture energy demand (∼8.5 kWh/kg NH3) by optimizing heat recovery simplifying plant design.

Language: Английский

Citations

4
Enhancing aromatic hydrocarbon production via catalytic co-pyrolysis of cabbage waste and low-density polyethylene using Fe-modified ZSM-5 catalyst DOI

Tayyaba Mubashir,

Aftab Farrukh,

Najam Ul Hassan

et al.

Biomass Conversion and Biorefinery, Journal Year: 2025, Volume and Issue: unknown

Published: Jan. 7, 2025

Language: Английский

Citations

0
Effect of Annealing Temperature on the Microstructural and Mechanical Properties of Wire Rod Steel Annealed Using a Biomass Gasifier DOI Creative Commons

Pathompong Chootapa,

Songkran Wiriyasart,

Sommas Kaewluan

et al.

Energies, Journal Year: 2025, Volume and Issue: 18(8), P. 1912 - 1912

Published: April 9, 2025

Natural and liquefied petroleum gases are widely used in industrial heat treatment. However, the rising cost of gas, combined with increased demand, has significantly impacted production costs environment. The annealing process typically relies on natural or as primary source. In this study, we aimed to investigate use biomass fuel a replacement for fossil fuels evaluate mechanical properties microstructure wire rod steel after using indirect from gasifier. We experimented examine effects temperatures 650 °C, 700 °C (below critical temperature Ac1), 750 (above Ac1 but below upper Ac3). batch furnace, made stainless steel, was modified traditional furnace that originally CNG LPG gas burners. It adapted into connected cross-draft furnace’s interior designed spiral cooling fins minimize energy consumption shorten time. Additionally, it substitute fuel, reducing environmental pollution. coated thermal insulation, gasifier stove device air feeding at 20 m3/h secondary supplied constant flow rate 32 m3/h, 36 40 m3/h. As source, eucalyptus. were measured terms tensile strength torsion, following TIS 138-2562 standard. This standard specifies must be least 260 MPa. Regarding requirements state withstand 75 rounds twisting without breaking. Our results showed soaking time 30 min subsequent 24 h, values 494.82, 430.87, 381.33 MPa, respectively. torsion 126.92, 125.8, 125.76 rounds, ferrite grain size temperature, reaching maximum °C. total duration each 2 h 10

Language: Английский

Citations

0