Cited by Investigation on the mechanism of air/condensate bubble flotation of emulsified oil droplet

Flocculation of emulsified oil-in-water with dodecylbenzene sulfonate and polyacrylamide and floc separation by dissolved air flotation DOI

ARA Scharnberg,

HA Oliveira,

SE Weschenfelder

et al.

Colloids and Surfaces A Physicochemical and Engineering Aspects, Journal Year: 2023, Volume and Issue: 669, P. 131496 - 131496

Published: April 21, 2023

Language: Английский

Citations

Flotation mechanism and performance of air/condensate bubbles for removing oil droplets in the presence of acetic acid DOI

Ce Wang, Yuling Lü,

Hongwei Qi

et al.

The Science of The Total Environment, Journal Year: 2024, Volume and Issue: 927, P. 172311 - 172311

Published: April 8, 2024

Language: Английский

Citations

Emulsions in porous media from the perspective of produced water re-injection – A review DOI

Ilgar Azizov,

Marcin Dudek,

Gisle Øye

et al.

Journal of Petroleum Science and Engineering, Journal Year: 2021, Volume and Issue: 206, P. 109057 - 109057

Published: June 3, 2021

During offshore production, it is typical to discharge produced water into the sea after treating a level that meets environmental regulations. A growth in volumes of and increasingly stringent requirements have drawn attention re-injection as more viable disposal method. Produced regarded an environmentally friendly cost-efficient approach allows integration with reservoir management. However, loss injectivity, due plugging pores by oil droplets particles present water, limits implementation re-injection. This review discusses engineering challenges during summarizes knowledge gaps literature on permeability reduction flow dilute oil-in-water emulsions. First, short introduction origins its composition, treatment techniques employed are provided. An overview injection strategies well discussion past field experience given. followed detailed diluted emulsions through porous media from perspective. models for predicting The physical parameters affecting droplet retention physicochemical interactions between pore walls discussed. studies investigated co-injection solid included well. identified effect stability, viscosity, wettability, not sufficiently examined. It was found drop-to-pore size ratio crucial factor retention, but often omitted industry. outlook suggestions address them Microfluidics pointed out complementary technique coreflooding.

Language: Английский

Citations

Adsorptive batch and biological treatments of produced water: Recent progresses, challenges, and potentials DOI

Maryam A. Al-Kaabi,

Nabil Zouari,

Dana Adel Da’na

et al.

Journal of Environmental Management, Journal Year: 2021, Volume and Issue: 290, P. 112527 - 112527

Published: April 22, 2021

Language: Английский

Citations

Bioremediation of Oil and Natural Gas Industry Waste Using Methanogens: Current Status and Future Perspective to Biohythane Production DOI

S. Saranya,

L. Thamanna,

V. P. Sreekutty

et al.

Arabian Journal for Science and Engineering, Journal Year: 2024, Volume and Issue: unknown

Published: Aug. 4, 2024

Language: Английский

Citations

Braid-reinforced PVDF hollow fiber membranes for high-efficiency separation of oily wastewater DOI

Tijjani El‐badawy, Mohd Hafiz Dzarfan Othman, Mohd Ridhwan Adam

et al.

Journal of environmental chemical engineering, Journal Year: 2022, Volume and Issue: 10(2), P. 107258 - 107258

Published: Jan. 24, 2022

Language: Английский

Citations

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity DOI

Y.. Li,

Jirui Hou,

Weipeng Wu

et al.

Petroleum Science, Journal Year: 2023, Volume and Issue: 21(1), P. 683 - 693

Published: Aug. 18, 2023

Conformance control and water plugging are a widely used EOR method in mature oilfields. However, majority of conformance agents unavoidable dehydrated situation high-temperature high-salinity low permeability reservoirs. Consequently, novel system HPF-Co gel, based on stabilizer (CoCl2·H2O, CCH) is developed. The bulk gel has better performances with high temperature (120 °C) salinity (1×105 mg/L). According to Sydansk coding system, the strength CCH increased code G. dehydration rate 32.0% after aging for 150 d at 120 °C, showing excellent thermal stability. rheological properties HPF also studied. results show that storage modulus (G′) always greater than gel. effect microstructure denser network, diameter three-dimensional network skeleton 1.5–3.5 μm. After 90 aging, still good structure. Infrared spectroscopy forms coordination bonds N O atoms amide group, which can suppress vibration cross-linked sites improve stability temperature. Fractured core test determines optimized polymer injection strategy velocity exceeding 98%. Moreover, subsequent waterflooding recovery be improved by 17%.

Language: Английский

Citations

Predicting the Performance of Lithium Adsorption and Recovery from Unconventional Water Sources with Machine Learning DOI

Ziyang Xu,

Yihao Ding,

Soyeon Caren Han

et al.

Water Research, Journal Year: 2024, Volume and Issue: 266, P. 122374 - 122374

Published: Sept. 7, 2024

Language: Английский

Citations

Produced water integration in CO2 storage using different injection strategies: The effect of salinity on rock petrophysical, mineralogy, wettability and geomechanical properties DOI

Stella I. Eyitayo,

Talal Gamadi,

Ion Ispas

et al.

Journal of Environmental Management, Journal Year: 2024, Volume and Issue: 372, P. 123307 - 123307

Published: Nov. 20, 2024

Language: Английский

Citations

Progress in treatment of oilfield produced water using membrane distillation and potentials for beneficial re-use DOI

Tijjani El‐badawy, Mohd Hafiz Dzarfan Othman, Takeshi Matsuura

et al.

Separation and Purification Technology, Journal Year: 2021, Volume and Issue: 278, P. 119494 - 119494

Published: Aug. 18, 2021

Language: Английский

Citations