An overview of traditional and advanced methods to detect part defects in additive manufacturing processes DOI
Vivek V. Bhandarkar, Harshal Y. Shahare, Anand Prakash Mall

et al.

Journal of Intelligent Manufacturing, Journal Year: 2024, Volume and Issue: unknown

Published: Sept. 2, 2024

Language: Английский

Progress in Vat Photopolymerisation Additive Manufacturing of Ceramic Lattice Structures and Applications DOI

Qumail Arshad,

Muhammad Saqib, Muhammad Sajid Arshad

et al.

Thin-Walled Structures, Journal Year: 2025, Volume and Issue: 209, P. 112918 - 112918

Published: Jan. 6, 2025

Language: Английский

Citations

2
Three-dimensional printing of complex structured silica glass based on high-strength green parts DOI
Yazhou Peng, Wenyue Zhao, Zhao Wang

et al.

Additive manufacturing, Journal Year: 2025, Volume and Issue: unknown, P. 104725 - 104725

Published: Feb. 1, 2025

Language: Английский

Citations

1
Polymer Characterization Techniques to Accelerate Discovery in Vat Photopolymerization and UV- Assisted Direct Ink Write 3D Printing DOI
Garvit Nayyar, Christopher B. Williams, Timothy E. Long

et al.

Polymer, Journal Year: 2025, Volume and Issue: unknown, P. 128355 - 128355

Published: April 1, 2025

Language: Английский

Citations

1
Effect of printing layer orientation and polishing on the fatigue strength of 3D-printed dental zirconia DOI Creative Commons
Yuqing Lu, Li Wang, Amanda Maria de Oliveira Dal Piva

et al.

Dental Materials, Journal Year: 2023, Volume and Issue: 40(2), P. 190 - 197

Published: Nov. 17, 2023

The aim of the study was to evaluate influence surface polishing and printing layer orientation on fatigue behaviour 3 mol% yttria-stabilized zirconia (3Y-TZP) by stereolithography (SLA) in comparison with subtractive manufacturing.

Language: Английский

Citations

18
Silicon carbide whiskers reinforced silicon carbide ceramics prepared by vat photopolymerization and liquid silicon infiltration DOI

Qianlong Fu,

Shiquan Sui,

Yuting Ma

et al.

Ceramics International, Journal Year: 2024, Volume and Issue: 50(10), P. 17747 - 17755

Published: Feb. 21, 2024

Language: Английский

Citations

9
Preparation and properties of Si3N4 ceramics via vat photopolymerization using Si3N4 powders coated with bowl-like boehmite DOI
Qiwen Wang, Jia‐Min Wu,

Chong Tian

et al.

Additive manufacturing, Journal Year: 2024, Volume and Issue: 84, P. 104137 - 104137

Published: March 1, 2024

Language: Английский

Citations

9
Preparation of high-density green body based on binder jetting 3D printing using spheroidized SiC powder DOI

Yulong She,

Jie Tang, Chaoyang Wang

et al.

Ceramics International, Journal Year: 2024, Volume and Issue: 50(18), P. 32412 - 32419

Published: June 5, 2024

Language: Английский

Citations

9
Enhancing 3D printed ceramic components: The function of dispersants, adhesion promoters, and surface-active agents in Photopolymerization-based additive manufacturing DOI Creative Commons
Klaudia Trembecka‐Wójciga, Joanna Ortyl

Advances in Colloid and Interface Science, Journal Year: 2024, Volume and Issue: 332, P. 103251 - 103251

Published: July 20, 2024

In the domain of photopolymerization-based additive manufacturing (3D vat printing), ceramic photopolymer resins represent a multifaceted composite, predominantly comprising oligomers, fillers, and photoinitiators. However, synergy between fillers polymer matrix, along with stabilization homogenization is facilitated by specific additives, notably surface-active agents, dispersants, adhesion promoters. Although these additives constitute minor fraction in terms volume, their influence on final properties material substantial. Consequently, meticulous selection integration are crucial, subtly guiding performance characteristics resultant matrix composites toward enhancement. This review delves into array dispersants coupling agents utilized components. It elucidates interaction mechanisms examines how interactions affect process. Furthermore, this investigates impact various rheological behavior slurries subsequent effects post-manufacturing stages, such as debinding sintering. also addresses challenges prospects optimization for advanced applications.

Language: Английский

Citations

9
Complex shapes of lithium disilicate glass-ceramics developed by material extrusion DOI Creative Commons
Manuel Fellipe Rodrigues Pais Alves, Claudinei dos Santos, Isabel Duarte

et al.

Additive manufacturing, Journal Year: 2024, Volume and Issue: 80, P. 103973 - 103973

Published: Jan. 1, 2024

The fabrication of high-end ceramics by additive manufacturing gained increasing research interest due to the capacity these techniques break through limitations traditional extractive manufacturing. Although efficient strategies for processing ceramic materials have been shown, with notable examples in dental field, dense glass-ceramics same means is almost unexplored. Herein, a strategy manufacture complex shapes lithium disilicate material extrusion detailed shown first time. An aging behaviour was observed on glass loaded aqueous suspensions and in-deep studied, being related leaching Li+ ions. Based this, hydrogel-based ink high solid content (ϕ≈ 50 vol%), suitable rheological properties (G´≈106 τ ≈1500 Pa) recovery time developed. By using optimized ink, propeller component aspect ratio small internal connected channels, as well crown were successfully printed. A debinding schedule tuned combination differential thermal analysis hot stage microscopy. sintered glass-ceramic parts presented good relative density (≈ 96.7 ± 0.8%) translucency. Outstanding mechanical achieved (Hv ≈5.3 GPa, KIf ≈2.1 MPa.m0.5, σ ≈279 44 MPa), comparable values usually attained powder technology. low deviation flexural strength data reported here absence meaningful defects analysed fracture surfaces homogeneous distribution residual porosity microporous, resulting Weibull characteristic σ0 = 301 MPa. results present work emphasized potential Direct Writing, technique, fabricate geometries, crowns.

Language: Английский

Citations

8
Viscoelastic Paste-Based Ceramic vat Photopolymerization: Recent Achievements and Future Developments DOI Creative Commons
Zhanwen Xing, Weiwei Liu,

Hongzhi Zhou

et al.

Deleted Journal, Journal Year: 2024, Volume and Issue: 3(1), P. 200111 - 200111

Published: Jan. 21, 2024

Ceramic vat photopolymerization (VPP) enables the fabrication of complex components with excellent properties and high precision. However, compared metals polymers, industrial application ceramic VPPs remains relatively limited. This can be attributed to challenges associated feedstock printability, complexity printing process, insufficient performance evaluation, service verification. To overcome these limitations, design a viscoelastic paste corresponding VPP strategies offer promising solution. paper presents review research on state paste-based VPP. The main technical aspects, including design, support strategies, green-body cleaning, subsequent post-treatment, are discussed. Furthermore, representative applications for various types advanced ceramics surveyed. also highlights involved provides suggestions addressing issues. Finally, future directions promoting additive manufacturing enhanced efficiency reliability

Language: Английский

Citations

8